The Salvajor 208 V Single Phase Garbage Disposal is a powerful and efficient way to dispose of food waste. It is easy to install and use, and it can help you to keep your kitchen clean and sanitary. This article will provide you with a wiring diagram for the Salvajor 208 V Single Phase Garbage Disposal, as well as instructions on how to install it.
Wiring DiagramThe following wiring diagram shows how to connect the Salvajor 208 V Single Phase Garbage Disposal to your electrical system.
Installation InstructionsTo install the Salvajor 208 V Single Phase Garbage Disposal, you will need the following tools and materials: * A Phillips head screwdriver * A tape measure * A level * A utility knife * A hacksaw * A pipe wrench * A bucket * A water hose * A GFCI outlet * A 12-gauge wire * A wire nut * A grounding clamp
Step 1: Prepare the Disposal1. Remove the garbage disposal from the box. 2. Unscrew the four screws that hold the disposal to the cardboard insert. 3. Carefully remove the cardboard insert. 4. Inspect the disposal for any damage. 5. If there is any damage, do not install the disposal. Contact the manufacturer for a replacement.
Step 2: Mount the Disposal1. Find a suitable location for the disposal. 2. The disposal should be located under the sink, with the drain opening facing down. 3. The disposal should be at least 18 inches away from the wall. 4. The disposal should be level. 5. Mark the location of the disposal on the floor.
Step 3: Cut the Hole1. Use a utility knife to cut a hole in the sink cabinet. 2. The hole should be large enough to fit the disposal. 3. The hole should be centered on the drain opening of the disposal. 4. The hole should be at least 18 inches deep.
Step 4: Connect the Disposal to the Drain1. Insert the drain hose of the disposal into the drain opening of the sink. 2. Use a pipe wrench to tighten the drain hose. 3. Make sure that the drain hose is not kinked.
Step 5: Connect the Disposal to the Power1. Find the GFCI outlet that you will be using to power the disposal. 2. The GFCI outlet should be located within 6 feet of the disposal. 3. The GFCI outlet should be protected by a 15-amp circuit breaker. 4. Connect the black wire of the disposal to the black wire of the power cord. 5. Connect the white wire of the disposal to the white wire of the power cord. 6. Connect the green wire of the disposal to the grounding screw of the GFCI outlet.
Step 6: Test the Disposal1. Turn on the water to the sink. 2. Turn on the power to the disposal. 3. Press the start button on the disposal. 4. The disposal should start to grind the food waste. 5. Allow the disposal to run for a few seconds. 6. Turn off the power to the disposal. 7. Turn off the water to the sink.
TroubleshootingIf the disposal is not working properly, there are a few things that you can check: * Make sure that the disposal is plugged in and turned on. * Make sure that the drain hose is not kinked. * Make sure that the disposal is not clogged. * If the disposal is still not working, you may need to call a qualified plumber.
Food Waste Disposers
Salvajor 200 Commercial Garbage Disposer 208v 2 Hp
Salvajor 100 Disposer Basic Unit Only 1 Hp Motor 208v 3ph
S Model 75
Salvajor 300 Sm Smaster Sping Pre Flushing Disposer 3 Hp 208v 3ph
Installation Care Use Manual Commercial Disposer
Pre Wired Control Panels
Salvajor 100 Commercial Garbage Disposal 1 Hp
Salvajor 100 Instructions And Operating Manual Pdf Manualslib
Installation Operating Salvajor
Install Man Tv
Salvajor 200 Commercial Garbage Disposer W Auto Reversing 208 230 460 V Ph 3 Restaurant Equipment Charlotte Gastonia Nc Your Guys
Food Waste Disposers
Food Waste Disposer